Product added to your wishlist! View wishlist
Sign in to see your saved products on any device
Product removed from your wishlist! View wishlist
Sign in to see your saved products on any device
Something went wrong. Please try again later.
Product is added to compare already. Please refresh the page.
Product is not found in compare. Please refresh the page.
5 Products already added. Please delete existing selection to add this.
Share this product
Rockler Woodcut Tools Bowlsaver Max4 Bowl Coring System
This product ad may change over time
ShareRockler Woodcut Tools Bowlsaver Max4 Bowl Coring System
The Woodcut Tools Bowlsaver Max4 is money in the bank, allowing you to quadruple your turning output by getting up to 4 nested bowls from a single large bowl blank. Material that would have otherwise been reduced to shavings can now be turned into three additional bowls that can be sold as the perfect grain-matched set. The Bowlsaver Max…
The Woodcut Tools Bowlsaver Max4 is money in the bank, allowing you to quadruple your turning output by getting up to 4 nested bowls from a single large bowl blank. Material that would have otherwise been reduced to shavings can now be turned into three additional bowls that can be sold as the perfect grain-matched set. The Bowlsaver Max4 Bowl Coring system works on bowl blanks up to 18' in diameter, using a semi-circular cutter to scoop out most of the waste, leaving a perfect blank for subsequent bowls. This blank can then be hollowed in the same way, leaving a third and fourth bowl blank. The Bowlsaver Max4 is attached to the lathe via the lathe tool post and is also supported at the tailstock for minimal vibration. It includes three blades with Stellite cutters that withstand shocks caused by knots and nails producing great results with either seasoned or unseasoned timber. If turned unseasoned, the resulting bowl blanks can be set aside for seasoning and finishing at a later date. Includes 1' Diameter Tool Rest Post. Woodcut Tools Bowlsaver Max4 Bowl Coring System Details: Save wood, money and time spent hollowing out your bowlsPrecision-machined aluminum and mild steel withstands tremendous forces from bowls small or large, wet or dryPredictable results every time, with either green or seasoned woodStable setup uses both the tool rest and tail stock on your latheIncludes three high-strength knives with Stellite CuttersRemoves bowls from 3' to 18' in diameter from inside the mother bowlUse on lathes with a swing from 16' to 25', and a motor of 1.5HP or greaterStellite cutters provide a fine finish and excellent durability on hard and soft woodsIncludes detailed 1' Tool Rest Post, user guide and ready-to-use planning templates to successfully core a nest of bowls NOTE: A lathe of at least 1.5HP is required for using this product. | Rockler Woodcut Tools Bowlsaver Max4 Bowl Coring System
Description
The Woodcut Tools Bowlsaver Max4 is money in the bank, allowing you to quadruple your turning output by getting up to 4 nested bowls from a single large bowl blank. Material that would have otherwise been reduced to shavings can now be turned into three additional bowls that can be sold as the perfect grain-matched set. The Bowlsaver Max4 Bowl Coring system works on bowl blanks up to 18' in diameter, using a semi-circular cutter to scoop out most of the waste, leaving a perfect blank for subsequent bowls. This blank can then be hollowed in the same way, leaving a third and fourth bowl blank. The Bowlsaver Max4 is attached to the lathe via the lathe tool post and is also supported at the tailstock for minimal vibration. It includes three blades with Stellite cutters that withstand shocks caused by knots and nails producing great results with either seasoned or unseasoned timber. If turned unseasoned, the resulting bowl blanks can be set aside for seasoning and finishing at a later date. Includes 1' Diameter Tool Rest Post. Woodcut Tools Bowlsaver Max4 Bowl Coring System Details: Save wood, money and time spent hollowing out your bowlsPrecision-machined aluminum and mild steel withstands tremendous forces from bowls small or large, wet or dryPredictable results every time, with either green or seasoned woodStable setup uses both the tool rest and tail stock on your latheIncludes three high-strength knives with Stellite CuttersRemoves bowls from 3' to 18' in diameter from inside the mother bowlUse on lathes with a swing from 16' to 25', and a motor of 1.5HP or greaterStellite cutters provide a fine finish and excellent durability on hard and soft woodsIncludes detailed 1' Tool Rest Post, user guide and ready-to-use planning templates to successfully core a nest of bowls NOTE: A lathe of at least 1.5HP is required for using this product. | Rockler Woodcut Tools Bowlsaver Max4 Bowl Coring System